Call Us

Workplace exposure limits: what changes on 1 December 2026

Rebecca Leigh

November 17, 2026

On 1 December 2026, the Workplace Exposure Standards stop being the benchmark for airborne contaminants in Australian workplaces. The list most WHS managers have quoted for years is being retired.

Its replacement is the Workplace Exposure Limits list, or WEL. Plenty of people have seen the acronym in a regulator newsletter and filed it as a rebrand. It isn’t. Some of the numbers have moved, and 33 carcinogens no longer have a numerical limit at all.

If you’ve got monitoring results on file, check them against the new list before December. A result that passed last year can fail next year without anything in your workplace changing.

Why “limit” replaced “standard”

WHS ministers settled on the new name in October 2019, as part of a decision to keep the limits mandatory and review them more efficiently. A standard reads like a target with a bit of give in it. A limit reads like a line, and Safe Work Australia describes it as a level that should not be exceeded.

The new term also lines up with international practice. The UK’s Health and Safety Executive, for example, has published its own Workplace Exposure Limits in EH40 for years. If your business reports exposure data in more than one country, you’ll now use the same vocabulary in each of them. This is a small win, but a real one.

Some of the numbers have changed

Individual limits have changed value, and Safe Work Australia’s comparison table runs to several pages of them. Some have dropped, some have risen, and a few entries have been merged or removed. The concentration that was acceptable under the WES isn’t the benchmark you’ll be measured against from December for a good number of substances.

The review also gave 31 substances a limit for the first time, diesel particulate matter among them, so some businesses will find a contaminant on their risk register that’s never been there before.

Manganese in welding fume shows how this plays out. The WES limit for manganese fume was 1 mg/m³. The WEL replaces it with a single entry for fume, dust and compounds: 0.1 mg/m³ for the inhalable fraction and 0.02 mg/m³ for the respirable fraction. Say a fabrication shop’s last inhalable result was 0.4 mg/m³. That passed comfortably last year. Against the WEL it’s four times over, with the same process, the same extraction, the same controls and the same people on the tools. The benchmark moved while the air stayed where it was. So “we tested that last year and it was fine” stops being a safe thing to say.

The 33 substances with no safe number

Safe Work Australia has identified 33 substances as non-threshold genotoxic carcinogens, or NTGCs. Chromium VI compounds, ethylene oxide and vinyl chloride monomer are on the list. They turn up in stainless steel welding, chrome plating, medical device sterilisation and PVC manufacturing.

From 1 December 2026, these substances don’t have a numerical exposure limit. That isn’t a drafting oversight. Safe Work Australia’s position is that NTGCs can’t be assigned a practical safe level of exposure, because of limited data and the nature of their effects, so there’s no number to publish.

For a business handling any of the 33, the question changes. It used to be “are we under the limit?” Now it’s whether you’ve eliminated the substance, replaced it with something safer where possible, or reduced the risk as much as reasonably practicable, and whether your records show it. That’s a harder test to pass, and it needs a documented answer.

Why the limits changed

Safe Work Australia reviewed the list against contemporary health evidence. The Australian Industry Group’s summary of the review puts it at roughly 700 substances and mixtures, and WHS ministers approved the revised list after extensive consultation.

That explains why the changes are uneven. Most limits stay put. Some shift because the evidence did. The NTGCs needed a different approach altogether.

Who needs to pay attention

It’s easy to file this under mining or manufacturing, however it wouldn’t be correct.

Dusts, fumes, gases, vapours and mists turn up wherever physical work happens: welding bays, commercial kitchens, laboratories, construction sites cutting engineered stone, printing shops and panel beaters. If your work generates any of them, the WEL change applies to you, however far you feel from heavy industry.

If you already monitor under the WES, you’ve got data that needs rereading against the new list before you rely on it. If you’re setting up monitoring for the first time, build it against the WEL list. There’s no point designing a program around a list that retires in December.

Businesses operating in more than one state have an extra step. Safe Work Australia says the WEL list takes effect once it has been implemented in the WHS laws of the Commonwealth, states and territories, with a harmonised transition period ending on 30 November 2026. That’s the national position. Your own regulator’s page is where to confirm how it applies in your state or territory before you assume one date covers everywhere.

The window is shorter than it looks

Until 30 November 2026, the WES list is still the legal benchmark. From 1 December, it’s the WEL list.

On paper that’s a clean handover. In practice, comparing your existing results, finding where a limit has tightened and checking whether your controls still hold up all take time most businesses haven’t set aside. You can’t rebuild a monitoring program in the last fortnight of November.

Work backwards from 1 December. If the comparison turns up a tightened limit, you’ll need time to arrange fresh sampling, review the controls and maybe change a process or a product. Occupational hygienists are likely to be booked out in the weeks before the deadline, because every other business on the list is working to the same date.

Where we’d start this month

We’d skip the big project plan and start with one comparison. Pull your last set of monitoring results and put them next to the WEL list, substance by substance. It’ll take an afternoon, maybe less, and it tells you whether December is a non-event for your business or whether there’s a gap to close.

After that, check your contaminant register covers everything your work actually produces, check it against the 33 NTGCs, and give the follow-up to a named person.

Then talk to the floor. Supervisors and operators know about new materials, process changes and workarounds that never made it into the paperwork. An hour with them is a cheap way to find gaps before a monitoring result does.

The next post in this series looks at the detail: which groups of limits have shifted, and how to tell a paperwork update from a real control problem.

How AuditCo supports the WEL transition

Our WEL Exposure Profile Consult is an independent check of your monitoring results, contaminant register and existing controls against the incoming WEL list, with clear findings on where you stand before 1 December 2026. If you operate across several states or countries, our auditors check your position in each jurisdiction instead of assuming one answer fits all of them.

To book a WEL Exposure Profile Consult, contact our team today.

Related Articles

HACCP in Practice: The Difference Between a Plan That Works and One That Sits in a Binder

July 30, 2026

WH&S Risk Management in Early Learning Centres: Governance, Compliance and the Duty of Care Imperative

July 29, 2026

ISO 9001 for Logistics Providers: What Quality Management Means When Your Product Is Service

July 28, 2026